How To Repair Vinyl Siding

15 Minute Vinyl Siding Repair With a Zip Tool. HGTV expert Henry Harrison shows how you can reattach it using a vinyl siding removal tool also known as a zip tool.

Repairing A Hole In Vinyl Siding Youtube

Use a table saw or circular saw to cut a new piece of vinyl siding.

How to repair vinyl siding. The top of the panel should fit underneath the siding above it. Level the Surface Using a utility knife or razor cutter cut away any protruding parts of the edge of the hole. You can mend small holes such as nail holes with exterior caulk designed to stick to vinyl.

Allow it to completely dry then use a razor scraper to cut the excess caulk flush with the outside of the siding. Use tin snips to make clean cuts around the damaged siding and remove it. Squirt a generous dollop of exterior caulking that matches the color of the siding into the hole.

Lay a bead of caulk along the back of the patch and set the patch into place. If youre considering making a repair youve probably completed this step but in favor of being thorough you should walk around your home and briefly look for additional damaged locations. Take a 12 or 34 inch long screw find a drain hole on the bottom of the vinyl siding board and drill a screw up from the bottom.

Be careful because older siding can become brittle. Make sure this piece is slightly larger than the piece you removed. Wipe the area dry with a rag.

Slide the zip tool along the bottom edge to release the vinyl siding from the piece below it. You may want to wait for a warm day when the siding will be softer and more pliable. Remove Old Vinyl Siding Start fixing damaged vinyl siding by removing the broken piece.

Cut the siding using a utility knife with a new blade. Itll better match the house than brand-new siding. Then lock the siding back into place.

Starting at one end of the damaged piece push the end of the zip siding removal tool up under the siding until you feel it hook the bottom lip. The very first step to repairing vinyl siding is to locate the damaged spot. The patch should be larger than the piece you removed.

For larger dents cracks or holes start by cutting out the damaged segment of siding and removing it with a zip tool. To repair vinyl siding fill in minor imperfections with caulk and then paint it to match the rest of the siding once it cures. Cut a replacement panel that is 4 inches longer than the damaged section.

To make speedy work of cutting the siding use a quality layout square like the Stanley Quick Square that will give you a clean straight right angle cut when cutting the replacement section of vinyl siding. Apply Caulk Apply generous beads of butyl or gutter caulk on the adjacent siding about 12 inch from the edges of the cutout area. There are several ways to repair damaged vinyl siding depending on the extent of the damage.

Cut piece of faded siding from an inconspicuous spot to replace the damaged section. Lift the new panel into place by pushing on the bottom edge to make sure it hooks onto the lower piece. Fill in the hole with a tinted caulk that matches your siding or opt for a paintable version.

Prepare Your Replacement Vinyl Cut the replacement vinyl piece to the necessary length using a utility knife or saw. Squirt the caulk into the hole so it fills the area behind the siding until it sticks out just a little from the front of the hole. Cut the tip of your color-match vinyl siding caulk and fit the tube into your caulk gun.

Use a zip tool a small metal bar tool angled so it can reach under siding to lock or unlock where siding. Use a flat pry bar to remove the nails and the damaged section of siding. You are creating a flush surface to work with.

Use siding cleaner to clean the area around the puncture. If you simply have a small puncture in your vinyl siding repair is easy. In this video This Old House general contractor Tom Silva explains how to repair vinyl siding.

This locks the loose board into the board below it. The vinyl siding zip tool will save you loads of time. Run a bead of adhesive caulk around the back of the patch and set the patch in place top image.

The following steps will help you make these repairs in a matter of minutes. Use tin snips to cut out the damaged area Image 1. We dont often use this technique to hold siding together but it will still work.

Use framing square and utility knife to cut through face of siding. Repeat the previous step for the top of the siding piece. Cut the replacement piece of vinyl siding about 3 longer than the section you removed.

Use a table saw or circular saw to cut a patch from a good piece of vinyl. Small holes in your homes vinyl siding up to the size of a nickel are straightforward to repair. Patch the Damaged Area.

First remove the corner piece then slide the zip tool under the siding and loosen it up. Screw up from the bottom of the siding.

How Do I Repair A Hole In Vinyl Siding Angi